Shear Behavior of Reinforced Concrete Inverted-T Deep Beam

Hoda Shousha, Rasha T. S. Mabrouk, Akram Torkey

Abstract


Contrary to top-loaded deep beams, Inverted-T (IT) deep beams are loaded on ledges at the beam’s bottom chord. The presence of the load near the bottom of the beams creates a tension field in the web at the loading points. An experimental investigation was carried out in which 8 specimens of reinforced concrete IT deep beams were tested and the effect of the following variables was studied: changing the hanger diameter, hanger arrangement in terms of spacing and distribution distance, hanger reinforcement ratio, vertical and horizontal web shear reinforcement diameter, and spacing. In addition, all the tested beams had long ledges extending to the end of the beam. It was concluded that hanger reinforcement diameter and horizontal web shear reinforcement have an insignificant effect on the IT deep beam capacity. While the change in hanger arrangement, vertical web reinforcement, and ledge length has a significant effect on IT deep beam capacity. The maximum spacing of the hanger reinforcement and the minimum hanger reinforcement ratio passing through the load plate length will be studied in the following publication. A finite element model (FEM) was presented to predict the behavior of IT deep beams. The simulation was carried out using the ABAQUS 2017 software program. The results of the numerical model showed good agreement with the experimental program. Analysis using design codes was checked against the experimental data, where the computed beam capacities were compared to those obtained from the test results. The comparison showed a remarkable difference between the predictions using the design codes and the test results. Computation using design codes significantly underestimated the capacities of the beams.

 

Doi: 10.28991/CEJ-2023-09-05-04

Full Text: PDF


Keywords


Type Inverted-T Beam; Finite Element; Shear; Hanger; Reinforcement; Ledge.

References


ECP-203-2020. (2020). The Egyptian Code for Design and Construction of Concrete Structures. Housing and Building Research Center, Cairo, Egypt.

ACI 318-19. (2019). Building Code Requirements for Structural Concrete and Commentary. American Concrete Institute (ACI), Michigan, United States. doi:10.14359/51716937.

EN 1992-1-1 (2004). Eurocode 2: Design of concrete structures (Part 1-1): General rules and rules for buildings. European Committee for Standardization (CEN), Brussels, Belgium.

Graf, O., Brenner, E., & Bay, H. (1943). Experiments with a wall-like girder made of reinforced concrete. Deutscher Ausschuss Fur Stahlbeton, 99, 41–54. (In German).

Leonhardt, F. (1966). Wall-like beams, German Committee for Reinforced Concrete. Reinforced Concrete Structures. (In German).

Furlong, R. W., Ferguson, P. M., & Ma, J. S. (1971). Shear and anchorage study of reinforcement in inverted T-beam bent cap girders. Research Project No. 113-4, Center for Highway Research, University of Texas, Austin, United States.

Mirza, S. A., Furlong, R. W., & Ma, J. S. (1988). Flexural Shear and Ledge Reinforcement in Reinforced Concrete Inverted T-Girders. ACI Structural Journal, 85(5), 509–520. doi:10.14359/2790.

Furlong, R. W., & Mirza, S. A. (1974). Strength and serviceability of inverted T-beam caps subject to combined flexure, shear, and torsion. No. FHWA-RD-75-S0401 Final Report, Texas State Department of Highways & Public Transport, Austin, United States.

Mirza, S. A., & Furlong, R. W. (1985). Design of Reinforced and Prestressed Concrete Inverted T Beams for Bridge Structures. Journal - Prestressed Concrete Institute, 30(4), 112–136. doi:10.15554/pcij.07011985.112.136.

Smith, K. N., & Fereig, S. M. (1974). Effect of Loading and Supporting Conditions on the Shear Strength of Deep Beams. Special Publication, 42, 441-460.

Fereig, S. M., & Smith, K. N. (1977). Indirect Loading on Beams with Short Shear Spans. Journal of the American Concrete Institute, 74(5), 220–222. doi:10.14359/11005.

Cusens, A. R., & Besser, I. I. (1985). Shear Strength of Reinforced Concrete Wall-Beams Under Combined Top and Bottom Loads. Structural Engineer, 63 B(3), 50–56.

Tan, K. H., Kong, F. K., & Weng, L. W. (1997). High strength concrete deep beams subjected to combined top-and bottom-loading. Structural Engineer, 75(11), 191–197.

CIRIA Guide 2. (1977). Design of Deep Beams in Reinforced Concrete. Ove Arup and Partners, Construction Industry Research and Information Association, London, United Kingdom.

Fernandez Gomez, E. (2012). Design Criteria for Strength and Serviceability of Inverted-T Straddle Bent Caps. Ph.D. Thesis, University of Texas, Austin, United States.

Varney, N. L., Fernández-Gómez, E., Garber, D. B., Ghannoum, W. M., & Bayrak, O. (2015). Inverted-T beams: Experiments and strut-and-tie modeling. ACI Structural Journal, 112(2), 147–156. doi:10.14359/51687403.

AASHTO. (2020). AASHTO LRFD Bridge Design Specifications. American Association of State Highway and Transportation Officials, Washington, United States.

Garber, D. B., Varney, N. L., Fernández Gómez, E., & Bayrak, O. (2017). Performance of ledges in inverted-T beams. ACI Materials Journal, 114(2), 487–498. doi:10.14359/51689451.

Rai, P. (2021). Non-Linear Finite Element Analysis of RC Deep Beam Using CDP Model. Advances in Technology Innovation, 6(1), 01–10. doi:10.46604/aiti.2021.5407.

ABAQUS. (2017). SIMULIA User Assistance 2017, Dassault Systems Similia Corp. ABAQUS, Johnston, United States.

Ali, Y. A., Assi, L. N., Abas, H., Taresh, H. R., Dang, C. N., & Ghahari, S. A. (2023). Numerical Investigation on Effect of Opening Ratio on Structural Performance of Reinforced Concrete Deep Beam Reinforced with CFRP Enhancements. Infrastructures, 8(1), 2. doi:10.3390/infrastructures8010002.

ASTM C150/C150M-18. (2019). Standard Specification for Portland Cement. ASTM International, Pennsylvania, United States. doi:10.1520/C0150_C0150M-18.

ASTM C33/C33M-18. (2018). Standard Specification for Concrete Aggregates. ASTM International, Pennsylvania, United States. doi:10.1520/C0033_C0033M-18.

Birrcher, D., Tuchscherer, R., Huizinga, M., Bayrak, O., Wood, S. L., & Jirsa, J. O. (2009). Strength and serviceability design of reinforced concrete deep beams. No. FHWA/TX-09/0-5253-1, Center for Transportation Research, University of Texas, Austin, United States.

Walraven, J. C., & Bigaj-van Vliet, A. (2011). The 2010 fib Model Code for Structural Concrete: a new approach to structural engineering. Structural Concrete, 12(3), 139-147. doi:10.1002/suco.201100025.


Full Text: PDF

DOI: 10.28991/CEJ-2023-09-05-04

Refbacks

  • There are currently no refbacks.




Copyright (c) 2023 hoda Mohamed shousha

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.
x
Message